#1 Rated 24X7 Plumbing Companies Nightmute 99690 AK (844-456-4168)Posted by Lee in Plumbing Companies, on September 25, 2017
Plumbing Emergency Firms in Nightmute Alaska
24X7 Operation – Get FREE Quote Click to Call
Plumbing Companies Nightmute 99690 AK: Here is what you can do about your frozen water pipe
Is repairing a frozen water pipe on your to-do list? Then the frozen pipe repair tips given below might prove to be helpful for you. Frozen pipes are a very big problem. They create a lot of inconvenience to people as lack of water supply disrupts the daily routine. Frozen pipes have the potential to burst which can cause a lot of damage and lead to a huge repairing expense. That is important to know if you are willing to hire Plumbing Repair Services in Nightmute 99690 AK.
Pipes which are likely to get frozen
The pipes which are located on the outside walls of the house or in the basements and attics are more likely to freeze due to low exposure to heat. Places experiencing high temperatures throughout the year also have the tendency of getting frozen pipes when the temperatures suddenly drop. The water in the pipe freezes and exerts a pressure of about 2,000 pounds per square inch leading to cracks or sudden bursting of the pipes. When a pipe bursts it leads to a loss of hundreds of gallons of water amounting to a monetary damage of thousands of dollars.
Signs of a frozen water pipe
The most obvious sign of a frozen water pipe is when there is no water supply from that pipe despite the faucet being on. Frozen pipes usually have frost on them which is a clear indication of water being frozen inside the pipe. Another obvious sign is the low temperature outside. Only when the temperature falls to thirty two degrees Fahrenheit or below, does the water start freezing. This is the time when people need to start taking precautions to avoid the freezing of pipes. Do not forget this tip if you would like to look for Plumbing and Heating Contractors Nightmute 99690 AK.
When pipes are frozen, they develop a noticeable bulge. Icicles formed on the pipes are due to the leakage of water from a crack in the pipe which is a sign of a frozen or damaged pipe. Sometimes, the whole pipe might not be frozen. To detect frozen spots in the pipe, you can use an infrared thermometer. When you move the thermometer along the pipe, the frozen spots show a much lower temperature than the other parts of the pipe.
Frozen pipe repair tips
Despite taking all kinds of precautions, if your pipes get frozen, then you can follow some of the frozen pipe repair tips mentioned below to solve the problem.
Finding the root of the problem
If one of the faucets stops working, it is very likely that the other fixtures too have become blocked. The reason for this is that all the small pipes are connected to the main pipe. Only when there is a problem in the main pipe do the other small pipes get affected. So you need to locate the frozen spot in the main pipe. If the pipes of only one part of the house are blocked, then it is an indication that one of the branch pipes providing water supply to that part of the house is frozen.
Thawing a frozen pipe
Once you locate the root of the problem, you can start the process of thawing. You need to apply heat to the frozen area and wait for the ice to melt inside the pipe. However, before applying heat, you should always shut off the faucets and fixtures first. When the ice melts, you can turn on the faucets slowly for the melted water to drain and you can assess the damage caused due to freezing. The faucets should be kept on to avoid refreezing. The pressure of the blockage can cause cracks in the pipe which can be detected as the water supply begins and the pipe starts leaking in certain places. Thawing is essential to prevent the pipe from bursting. Cracks can be repaired but if the whole pipe bursts, there is no option other than installing a new pipe.
Your presence is necessary
When the process of thawing is going on, you should always stay close. The reason is that the heaters or hot water used to increase the temperature cannot be left unattended or they can cause more damage instead of helping you. Also, water damage due to a leak can be avoided if you are present on scene. The process of thawing is slow and patient work. So it is better to pay attention to it rather than spending more later in case the pipe bursts or your property gets damaged.
Using safe heat sources
You should avoid using open flame or a blowtorch as it can present a fire hazard. It can also lead to a rapid melting of the water which can exert pressure on the pipe and make it burst. Some safe heat sources are electric heating pads, high power hair dryers, infrared or incandescent heat lamps, portable heaters and electric pipe heating tape. That is really important when it comes to looking online for the top Plumbing Emergency Firms Nightmute 99690 AK.
Calling the plumber
If you are unable to detect the frozen spot or if the frozen spot is located underground or behind a wall, it is time to call the plumber before the pipe bursts. The plumber can expertly detect the problem and with minimum damage to your property can thaw the pipe. However, you need to be careful about how to choose your contractor. Call us today and we will help you find the best Plumbing Contractors Nightmute 99690 AK.
How to avoid refreezing of the pipes in the future?
The first thing that you need to do is to locate all the areas in your home which are susceptible to freezing. The area near the water lines should be kept warm. This can be done by insulating the walls, repairing broken windows and wrapping the pipes with foam insulating sleeves. There are some pipes which are more vulnerable to freezing than others. To prevent them from freezing, the faucets should be kept on so that a small trickle of water constantly flows. The loss of this water is bearable compared to the cost of repairing a damaged pipe. Outdoor pipes should be buried below the frost line and a twelve inch thick insulation should be provided to these underground pipes.
These are just a few frozen pipe repair tips which you can try out to get effective results. That is really important when it comes to choosing the best and top rated Plumbing Companies Nightmute 99690 Alaska.
Plumbing Companies Nightmute 99690 Alaska: General Tips!
#1 Rated 24X7 Plumbing Companies Anchorage 99512 AK (844-456-4168)
#1 Rated 24X7 Plumbing Companies Anchorage 99513 AK (844-456-4168)
Ways to Unclog Drains: Your dish detergent can unclog your pipe- Something as simple as a dish detergent can be used to remove obstacles from the drain pipe. You need to pour a small quantity of the liquid detergent down the drain and follow it up with some boiling water. The detergent can lubricate the sides of the drain and force the dirty residue to break into smaller components and the hot water can flush away the grease. You can make use of a plunger to push down the remaining dirt and clean your pipe.
Cleaning the Pipe: There are some plumbing jobs that I won’t do, but this one is easy. First, place an empty bucket underneath the U-shaped pipe (the trap) beneath the sink. The bucket will collect the water that will spill. Using a plumber’s wrench, loosen the slip nuts at both ends of the pipe. You should be able to finish the operation by hand. When the trap is free, remove it and turn it upside down, emptying the contents into the bucket. You may also need to fish around inside it for debris, and do the same with the pipes that were holding it. An old toothbrush is good for getting the tough gunk out. Rinse the trap with water and then put it all back together. In most cases, that will have done the trick.
Save Money on Bathroom Modelling – Consult an architect. Depending on the scale of your project, you might not need a full–on architectural commission, which involves extensive meetings, multiple job–site visits, and several sets of construction drawings, to the tune of about 8 percent of a project’s construction budget. You might be able to tap an architect’s design savvy by having him undertake a one–time design consultation. For example, for a $400 flat fee, Baton Rouge architect Kevin Harris will meet with a homeowner, examine the problem, and sketch out a few solutions that could be as simple as opening up a partition wall or moving a door. The homeowner can then give the sketch to a builder or take it to a drafting service, which will charge about $1 to $1.50 a square foot to crank out formal construction drawings.
Bathroom Design Tips – Curbless Shower with a Bench and Grab Bars – This doesn’t have to look as antiseptic as it sounds. Think in terms of a tiled shower area with recessed shelves at arm’s level to stop you from having to stoop down to the floor or reach up to a shower rack. Add a matching ceramic bench and grab bars that come in brushed nickel, chrome or bronze to match your faucet hardware. They will look more upscale than the white plastic hospital variety.
Look for Drips. Puddles of water on your basement floor are an obvious sign of a plumbing leak. But, in many cases, a loose valve or cracked pipe may simply cause condensation to build up in a specific area. Odor-causing bacteria and mold can begin to form in these places. If you suspect a leak, having your plumbing inspected by a Ragsdale professional can help you save money and avoid replacing damaged drywall and carpeting.
Check how well your toilets are flushing. In case the handle has to be played with in order to keep the water from running constantly, or if perhaps it needs to be held down many times in order to flush, you might need to switch out a number of the parts in your tank. This is not expensive, plus it might help lower your monthly water bill. It may also imply that you steer clear of the embarrassment of the flushing system breaking if you have visitors!
Consider a corner sink. If you’ve got a tight space with potential traffic-flow problems due to how the entry door or shower door swings open, then consider putting your sink in the corner to free up space.
Occasionally, the ferrules in a supply tube can get scratched or dented causing water to leak. Use Teflon tape around the ferrule until a permanent repair can be made.
Perform a pipe inspection to check for leaks. You may have to look into some hard to see places such as under the home so make sure you use a flashlight. If you find a water leak in a pipe, you will have to get it repaired or replaced. You will have to shut off the main water valve so it can be repaired. It is wise to hire a plumber to do the job.
Use a shop vacuum to remove hard objects. When a hard object like a toothbrush, comb or toy plugs a toilet or drain, a plunger may not be the solution—it might only push the obstruction in deeper. Instead, suck out the water and the obstruction with a wet/dry shop vacuum.
Make sure the float in your sump pump is free of obstructions
It is a wise idea to install flood alarms, which is a device that will alert you in case it comes in contact with water. This device is made to notify you of an impending flooding or serious leak problems.
Clean gutters, drains, and downspouts. Ridding gutters, drains, and downspouts of detritus prevents leaks as well as mildew and mold growth. Once your roof’s drainage system is clear, examine your property for plumbing vents. Check that each vent is clear of sticks, leaves, nests, and so forth. If you don’t have a tall, sturdy ladder to check high vents, you can call a plumbing repair company for assistance. Residential plumbers don’t just do plumbing repair – they also offer preventive, maintenance-oriented services.
Tips for installing and repairing a gas line: Make use of epoxy compounds when your gas line has a leak- Epoxy compounds can quickly create a rigid and strong bond and so they can seal the leaks in the gas line easily. This is a temporary repair solution which can save your time and expense and can last for a long time. Epoxy compounds contain resin and a hardener which are suitable for cast iron pipes. They can be poured over the leaks. The bond produced by the epoxy compounds is very effective in blocking gas leaks till you can get the pipe replaced.
Use a bucket of water to flush the toilet. You don’t have to run to the neighbor’s bathroom during a plumbing project. Before you turn off the water supply, fill 2- gallon buckets with water. Flush the toilet by dumping the water in the bowl. You’ll get one flush per bucket. Works just as well as the usual method, although it won’t refill the bowl.
Tips for installing and repairing a gas line: Always turn off the gas supply before installation or repair- This is a necessary step which should not be avoided. You should turn off the valve present beside the gas meter before removing the old pipe and replacing it with a new one and also while repairing the present one. In case the valve is open, gas can leak and can lead to a fatal disaster by causing a big fire. The valve should be perpendicular to the pipe when it is closed. There is no change in the gas meter when the valve is closed. You should check all this and then start the gas line work.
What to look for in your next contractor – A reputable plumber will not only provide you with a quote and upon request will give you a price ceiling if the problem goes beyond what expected. If the plumber can’t give you a quote over the phone because of the type of damage, ask for a “worst-case-scenario” quote.